Forum Comments

3D Chameleon T1 not working when printer has E2
In Support
woogerboy21
Dec 29, 2021
M82 ; turn absolute distances for the extruder G92 E0 ; go to holding position to unload the stock extruder G0 X6 Y211 F2000 ; <<----- EDIT THIS LINE TO SET THE INITIAL LOCATION OF THE BUTTON G91 ; move to relative mode {if previous_extruder>-1} ; cool (and size) in 1.8mm tube G0 E-20 F2800 ; quickly retract the filament to shape it G0 E-10 F600; slowly allow it to cool G0 E1 F2000 ; blob elimination ; back to tip size G0 E-20 F2800 ; quickly retract the filament to shape it G0 E-10 F600; slowly allow it to cool G0 E1 F2800 ; blob elimination G0 E-10 F2800 ; quickly retract the filament to shape it G0 E1 F2800 ; quickly ram the filament to shape it G0 E-10 F2800 ; quickly retract the filament to shape it G0 E1 F2800 ; quickly ram the filament to shape it ; back to 1.8 constriction G0 E-50 F2800 ; quickly retract the filament to shape it G0 E-80 F100; slowly allow it to cool ; turn the fan off M107 ; this printer has the fan in the way, so turn it off ; retract it back out of the extruder G92 E0 G0 E-165 F2000 ; out of extruder - press button to remove it all the way G91 ; move to relative mode G0 X3 Y3 F2000 ; press the button G4 P400 ; dwell for .3 seconds G0 X-3 Y-3 ; back off the button G4 S2; wait for it to happen G0 X3 Y3 F2000 ; press the button G4 P400 ; dwell for .3 seconds G0 X-3 Y-3 ; back off the button G4 S2; wait for it to happen G0 X3 Y3 F2000 ; press the button G4 P400 ; dwell for .3 seconds G0 X-3 Y-3 ; back off the button G4 S2 ; wait for it to happen ; select direction to pull filament out G0 X3 Y3 F2000 ; press the button G4 P3500 ; dwell for 3 seconds {if previous_extruder>1} G4 P2000 ; dwell for 2 more seconds seconds {endif} G0 X-3 Y-3 ; back off the button ; now press and hold for to let it unload G0 X3 Y3 F2000 ; press the button G4 S6 ;  <<---- INCREASE VALUE (S = Seconds) TIME IF IT DOESN'T UNLOAD FROM THE Y ADAPTER G0 X-3 Y-3 ; back off the button {endif} ; always reset to extruder 0 G0 X3 Y3 F2000 ; press the button G4 P1300 ; dwell for 1.3 seconds G0 X-3 Y-3 ; back off the button G4 S3; wait for it to happen ; press the button for each extruder (1,2,3) {if next_extruder>0} G0 X3 Y3 F2000 ; press the button G4 P400 ; dwell for .3 seconds G0 X-3 Y-3 ; back off the button G4 S1; wait for it to happen {endif} {if next_extruder>1} G0 X3 Y3 F2000 ; press the button G4 P400 ; dwell for .3 seconds G0 X-3 Y-3 ; back off the button G4 S1; wait for it to happen {endif} {if next_extruder>2} G0 X3 Y3 F2000 ; press the button G4 P400 ; dwell for .3 seconds G0 X-3 Y-3 ; back off the button G4 S1 ; wait for it to happen {endif} G4 S1 ; wait just a little longer ; load the filament G0 X3 Y3 F2000 ; press the button G4 P3500 ; dwell for 3 seconds {if next_extruder<2} G4 P2000 ; dwell for 2 more seconds {endif} G0 X-3 Y-3 ; back off the button ; now press and hold to load G0 X3 Y3 F2000 ; press the button G4 S6 ; << ------- INCREASE THE S10 (S = Seconds) VALUE TIME IF IT DOESN'T LOAD INTO THE STOCK EXTRUDER - This should match the above unload time G0 E15 F1500 ; << ------- ADJUST THE E50 VALUE TO STOP IT RIGHT AFTER IT LOADS INTO THE STOCK EXTRUDER (50mm is the default) G0 X-3 Y-3 ; back off the button G92 E0 ; now press it again to let go of the filament G0 X3 Y3 F2000 ; press the button G4 P400 ; press for 1/4 of a second to move to next G0 X-3 Y-3 ; back off the button G4 S1 ; wait for it to happen {if next_extruder>2} G4 S1 ; wait a little longer for it to happen {endif} G90 ; move back to absolte mode M83 ; but make sure the extruder stays in relative ; reload filament all the way into extruder G92 E0 G0 E345 F2000 ; <<<<<----------- EDIT THIS DISTANCE TO FINE TUNE THE FILAMENT LOADING TO STOP BLOBBING OR UNDEREXTRUSION G92 E0 M83 ; turn relative distances for the extruder M106 ; turn fans back on
0
0
woogerboy21
More actions
GreenLogoNoText.png